We seem to have run into a period in life when all the
machinery seems to have taken a wobble at the same time and cannot shake it
off. All attempts to put thing right have been thwarted and mechanics who are
working on them cannot just put their finger on the particular problem.
Take the Agrotron
tractor for instance, for a long while it had difficulty in drawing its
fuel from its own fuel tank, while working its was no trouble but left over
night and its fuel in the tank low, you would have to wind the engine for a
little while until it had pumped its fuel back up to the engine.
 |
| The Agrotron has done well over ten thousand hours, here its got the post knocker on, mounted on the front, this gives it more reach into difficult corners or on hedge banks and ditches, and its more convenient to see whats happening |
Over the months this got worse, the fuel must drop back to
the tank and drawing air into the system. It has a rubber pipe from the tank
over the transmition housing to the fuel pump, and this we replaced, but its
still getting air into the fuel pipe.
I need to fill the fuel tank to the top each night before I
stop it, in order for it to start properly the next day; the problem is more of
an air leak in the fuel lift pump I suspect.
Later we found it was the injector bleed off pipe that had fractured and causing the air to get into the fuel system, the main trouble was when running fuel was leaking into the sump, 'watering' down the engine oil.
The bleed off pipes are run along inside the rocker cover, and cannot be seen unless that cover is removed, however we found the trouble after months of trial and error, and it runs and starts well now.
The Land Rover
Discovery has a mystery fault that is defying all attempts to diagnose,
travelling home from town last Friday one corner of the vehicle started
sagging, and thought I had a puncture, I pulled onto the side of the road only
to find all the tyres were okay it was the air suspension had dropped on one
rear wheel, so I drove it home steadily with the rear mud flap just touching
the road and the wheel way up in the top of the wheel arch. Took it round to my
local garage who does the work on it for me and by the time I got there, in the
next village it had pumped itself back up, and stayed up.
 |
| This was when I first had it second hand, right now its in its "working cloths" and looking a bit more rural |
He put the diagnostic computer on it and found nothing amiss
and physically looked around the air bags and found no leaks.
So I fetched it back home and went down counting the cattle,
then parked it up on the yard, and within the next few minuets it had gone down
again.
The following day I backed it round pointing towards the
road, with the suspention still down at the bottom and turned Eileen’s car
round for her and we set off to take it back to the garage. Before I had done
twenty yards to the road it had pumped itself up to normal height, but we still
took it to be looked at again.
More and closer inspections of the air bags and pipes, still
no leaks, and onto the diagnostic computer revealed no electrical faults, so
next day fetched it back yet again.
It did it again, and got it to the garage with it “on its
arse” and left it there, he found that these air bags on these vehicles should
be changed every so many thousand miles,
and fitted new air bags, that seems to had ironed out the Discovery problems,
(until the rear door lock/latch jammed) even that has been mended now.
And also the JCB
Fastrac, I came home after hedge cutting one day, and it had got no brakes,
I contacted the lad who does my spanner work on the tractors and machinery ( I
do do the big hammer and welding repairs myself but internal work I leave to
them’s that should know) .
A low air red warning light was on, on the dash board which
suggested low air to the brake, or so you would think.
On looking round it said he knew nothing about air brakes
that the Fastrac should have. So I rang the chap who does my mowing and big
baling, he has had two Fastrac’s and he recommended the chap who had done
worked on his.
First thing he went
for was an air valve in the cab behind the right hand door, he removed it and
opened it with all the bits flying all over the place, the aluminium casing was
slightly corroded and we ordered a new one, which was fitted a few days later.
It did no good it was not that and it did not need a new one but it cost me
£110.00.
We found out then it does NOT have air brakes.
 |
| This tractor has ahd an easy life overall, it had spent most of its time with a mounted sprayer permanently fitted, and now spent the last few year since I have had it with a hedge cutter mounted on it, to my knowledge its never done a hard days work in its life, (about 8,000 hours on the clock) |
Next we/he looked round the slave cylinders on the brake
discs, for this we had got to jack it up and take a wheel off. With all the
wheel nut off the wheel would not move, it was froze onto the hub, so he hit a
few heavy blows with the sledge hammer and still did not move, but one blow had
grazed the tyre air valve and started it leaking. Then with a jack between the
chassis and the wheel rim we moved it and the wheel came off with a flat tyre.
We/he found nothing wrong with the cylinders or the brake
pads, but it cost me £40.00 to have the new valve fitted and the tyre blown up.
Then looked at the hydraulic pumps, thinking that the
smaller one was not putting out enough pressure to activate the brake, by the
way we/he did find out that the tractor only had two air tanks and that the
brakes did NOT work with the assistance of air, they are oil only. So I priced
up a new hydraulic pump, £870.00. (that was the problem in the end)
At this point I got the impression that he was way out of
his depth on tracing this braked problem, so did what I should have done in the
first place, I called out the JCB dealers mechanic, who, went round everything
that looked as though it had been disturbed and tested the pressures of various
pipes and valves only to find a pressure maintenance valve on the side of a
hydraulic block was not doing it job.
The mechanic said he would go back to the depot and order
the new valve, and it would be ready for me to pick up the following day (the
JCB factory where all JCB’s are made is only ten miles away at Rochester).
I had been given instructions that when I had got the valve,
a valve only as big as my thumb, to unscrew the old one out and screw the new
one in its place, the valve being all pre- set and ready to do its job. It did not make the brakes work, but it
turned out that swarf from the worn out hydraulic pump was jamming up the
working of the hydraulic block, this cleaned out (with another call out) the
brakes worked at last after almost two months out of commission.
And right now it’s the
chain saw, it will not start. Gradually over the last few months when I
have used it, it has got worse and worse to start, pulling and pulling on the
cord until ya fingers ready to drop off.
The saw is a relatively new one , not done muck work, and
still looks brand new, so I spoke to the chap who sold it to me, and he said “how
old is the fuel in its tank” and in the drum I’m using it from, it could be six
months old unleaded petrol (gas) fuel.
He suggested I tip the old fuel out and get some fresh fuel,
this I did and it still will not start. Pulled (screwed) the spark plug out and
found that there was no spark, no wonder it wonna start, so now I’m at the
point of a new spark plug, although the “old” one was dry and clean and still
looked like new.
When new it started on the third pull and it should do now,
do you have any suggestions as to why this critter won’t start?
All this has happened in the lasty two months of the old year (2011) were starting the new year with just the chain saw to sort out, thank goodness.
I’ve got a Little Breakdown,
I’ve got a little
breakdown and its needs attention now,
Take it to the
workshop, to bodge it up somehow,
Need to clear the
work bench, with scrap its piled high,
Things that needed
mending, I failed but had a try.
Spanners come in
sets, they’re spread all round about,
The very one your
wanting, one you conner do without,
Spend all morning
searching, and you end up with a wrench,
Round the corner off
the nut, then find its on the bench.
The metals rusty,
flaking off, got it to weld somehow,
Clean the edge and
got some gaps, must be done right now,
Spitter spatter stop
and start, resembles pigeon siht,
Grind it off and fill
the holes, and hope it wunna split.
Drill bits with the
edge knocked off, the saw it that hit a nail,
Hammer’s got a
headache, and it needs a brand new stale,
Screwdriver hit with
hammer, when the chisel conna find,
And the spirit level
lost its bubble, ta guess work I’m resigned.
Have a dam good clear
up, and throw the rubbish out,
Then look for where
you’ve chucked it, that little bit of spout,
Ventualy it all comes
back, n’ builds up on the floor,
Praps a bigger
workshop, cus I conna shut the door.
I’m really tidy in my
mind, but sometimes I forget,
When I’m in a hurry,
and black clouds and rain a threat,
Job is done, tools
chucked in, the workshop miss the bench,
It happens all the
while, but I stick with a big old wrench.
But on the whole I’m
not alone, but people don’t admit,
They pretend to be so
perfect, spanners back in tool box fit,
A breakdown always
happens, when you least expect it could,
Then back to get the
job done, as quick as ever should.
(Owd Fred)
A man too busy to
take care of his health is like a mechanic too busy to take care of his tools.
Spanish proverb.